Image Brightness by Tone Zone

Most brightness sliders add the same amount to every pixel, so lifting a dark face also turns a grey sky white. Here the shift splits into shadows, midtones, and highlights. Raise the dark side of a backlit portrait while the window behind stays put, check the clip counts, then save the full-size file. Your photo never leaves this tab.

Drop a photo here

Paste with Ctrl+V or pick a file. JPEG, PNG, WebP, GIF, BMP, and AVIF open in every current browser.

Before After
Tone curve

Which slider moves which pixels

Each zone slider pushes a band of tones up or down, strongest in the middle of its band and fading to nothing at the edges. The bands overlap, so a pixel at 40% grey takes a little from Shadows and a little from Midtones. No hard cut sits between zones, which is why a sky gradient stays smooth after a big move.

SliderTones it movesWhat usually sits thereNever moves
Shadows0% to 55% grey, strongest near 27%Hair, foliage, coat folds, a face against a windowPure black, anything above 55%
Midtones15% to 85%, strongest at 50%Skin, grass, painted walls, most product shotsPure black, pure white
Highlights45% to 100%, strongest near 73%Sky, lamp glow, white shirts, snowPure white, anything below 45%
OverallEvery tone, method decides howThe whole frameDepends on method, see below

Since all three zone sliders taper to zero at both ends of the scale, pure black and pure white never move under them. A Shadows push of +40 takes level 51 to 72 and level 26 to 34, while 0 stays 0 and middle grey 128 shifts by two levels. Only the Overall slider moves the end points.

Offset, Gamma, or Exposure for the Overall slider

The three methods give different results at the same slider value. Here is what +40 does to a grey ramp under each one.

Offset
Adds a fixed amount to every pixel. At +40, black becomes level 51 and every tone rises by 51 levels. Anything starting above 204 hits 255 and loses its texture. Blacks turn charcoal, so the photo looks foggy. Pick Offset for scans with a grey cast where the darkest point needs a reset anyway.
Gamma default
Raises each tone to a power. Black stays 0, white stays 255, middle grey 128 moves to 162. Nothing clips at either end, which makes Gamma the safest choice for a general brightness fix and the method Auto level picks.
Exposure
Multiplies light in linear space, the way a longer shutter time would. +40 equals 0.8 of a stop. Black stays 0, middle grey moves to 165, and every tone above 200 clips to white. Use Exposure on a whole frame shot too dark by a known amount, and watch the Blown to white figure.

Three common photos and the settings to start from

The chips in the settings panel load these values. Treat them as a first move, then nudge one slider at a time while watching the readout.

Backlit subject

Shadows +40 Highlights -10

A person in front of a bright window comes out as a dark shape. Shadows brings the face up into readable tones. Highlights at -10 holds the window from spreading into the curtains. If Blown to white climbs past about 2%, pull Highlights further down before touching Overall.

Flat overcast

Midtones +20 Highlights +10

Grey-sky photos bunch every tone in the middle of the histogram. Midtones lifts grass and buildings without lightening the deepest shade, so the image gains snap. Highlights at +10 makes the clouds read as white rather than dirty grey.

Night phone shot

Gamma +10 Shadows +25

Leave Highlights at 0 here. Street lamps already sit at 255 in the original, and no slider brings detail back into them. Lifting night shadows also lifts sensor noise. Run the result through the Noise Reduction tool if the dark sky turns grainy.

Reading the histogram and clip counts

The grey fill is the original photo, the colored fill is the edited one. Dark tones sit on the left, bright tones on the right. A brightness fix moves the colored hump to the right without stacking a spike against either wall. The curve plot beside it shows the exact mapping: the dashed diagonal means no change, anything above it means brighter.

  • Median tone is the level half the pixels sit below. Typical daylight photos land between 90 and 140. Under 60 reads as dark on most screens.
  • Crushed to black counts pixels at level 0 or 1. Silhouettes and night skies run high on purpose, so judge the change, not the number.
  • Blown to white counts pixels at 254 or 255. A jump from under 1% to 6% after one slider move means you erased cloud or skin texture.

Tick Show clipping to paint those pixels on the preview, red for white and blue for black. The overlay never ends up in the saved file.

Where this editor falls short

  • Blown areas stay blown. Lowering Highlights on a pixel at 255 turns flat white into flat grey. The clouds were never recorded, and no browser tool recovers them.
  • 8 bits per channel. Browser canvases hold 256 levels per channel. Pushing a JPEG past about 60 in either direction shows banding in smooth skies. A RAW file in a desktop raw editor takes the same push cleanly.
  • No RAW, limited HEIC. CR3, NEF, ARW, and DNG files do not open. iPhone HEIC photos open in Safari only. In Chrome or Firefox, export them as JPEG first.
  • No masking. Shadows lifts every dark area at once, the hair and the hedge behind it alike. Edits limited to one region need a layer editor.
  • Metadata is dropped. Saved files carry no EXIF, so the capture date, camera model, and GPS position are gone. Good for privacy, bad if you sort photos by date.
  • Size ceiling. The full-size export caps at about 16.7 megapixels, a browser canvas limit on many phones. Larger photos get scaled down to fit, and the note under the buttons says when this happens.

Image brightness questions

Short answers about zones, clipping, and saving.

Why does my near-black background lighten when I raise Shadows?

A background at 5 to 10% grey sits on the lower slope of the Shadows band, so it rises a few levels. True black at level 0 stays put. Set Overall to Offset and pull it down by 2 or 3 to bring the background back.

Does lowering Highlights bring back a white sky?

Only where the sky still holds some tone. Pixels already at 255 in the original carry no detail, so lowering them gives flat grey. Check Blown to white in the Before column. If it reads several percent, that area is gone for good.

What does Auto level change?

It reads the median tone, then sets Overall in Gamma mode to move that median toward level 117, about 46% grey. It adds Shadows +20 when over a quarter of the photo sits below 15% grey, and Highlights -20 when over 8% sits above 92%. The sliders show what it picked, so you adjust from there.

Should I save PNG or JPEG?

PNG keeps every pixel and any transparency, but a photo saved as PNG runs several times larger than the JPEG. JPEG saves at 92% quality and fills transparent areas with white. For photos headed to the web or a message, pick JPEG.

Why do saturated colors look duller in the saved file?

Recent iPhones and some cameras shoot in the Display P3 color space. The browser canvas works in sRGB, so the deepest reds and greens get pulled into the smaller sRGB range on load. Brightness values stay correct. The color shift happens before any slider moves.

Is my photo uploaded anywhere?

No. The file decodes inside your browser tab and all processing runs on your device. Toolexe receives no image data, and closing the tab clears the photo from memory.